Sartorius Mechatronics
Home
 Sartorius Omnimark      Mark 3 LTE Moisture Analyzer
 

Mark 3 LTE Moisture Analyzer
Simple. Dependable. Accurate. Fast.

Makr 3 LTE Moisture Analyzer

Out of the box solution at your fingertips!

Fast and accurate moisture or solids measurement with the Mark 3 LTE allows adjustments to be made in the processing cycle in minutes rather than hours. One button operation to perform a test. No pre-programming required on the part of the operator.

Thousands of material program settings already established for the following markets:

  • Pharmaceutical
  • Food
  • Chemical
  • Wastewater
  • Cosmetics
  • Ethanol
  • Pulp and paper
  • Paint and coating

Readers' Choice Awards

Mark 3 LTE Moisture Analyzer Brochure (PDF)

Mark 3 LTE Datasheet- Pulp & Paper (PDF)

Mark 3 LTE Datasheet- Snack Food (PDF)

Mark 3 LTE Datasheet- Chemicals and Minerals (PDF)

Specifications
Method of Measurement:Loss on drying
Components Analyzer Modular: Control and Heater modules
Optional Configuration Up to 2 Heater modules per Control module
Heat Source Four parallel infrared quartz cylinders
Temperature Steps Programmable one or two
Temperature Adjustment Optional fi xture for internal electronic two point with programmable prompt
Standby Temperature 30 – 160° C in one degree increments
Equilibration Time Programmable setting of time at Standby Temperature
Temperature Display Display of both target and current temp at each stage of drying and standby
Conserve Mode Clock Programmable time by day of week to shut down and wake up analyzer
Balance Capacity 40 Grams
Balance Resolution 0.001 grams
Balance Repeatability +/– 1 mg
Balance Calibration Manual
Balance Module Design Thermally isolated with inner and outer stainless steel containers
Balance Spill Protection Reservoir under draft shield to collect liquids, powders or pellets
Ideal Weight Audio and visual display for programmable target sample weight addition
Display of Results 0.01%
Recommended Working Range 0.1 to 99.9%
Target Limit Alert Minimum and maximum programmable limits and screen alert when test done
Program Storage 60 programs with unique settings, alphanumeric naming
Result Storage 999 individual results
Statistical Evaluation Average, SD, RSD, high and low
Units of Measure of Results Weight, % Moisture, % Solids, % Volatiles, Fuel Moisture, PPM
Endpoint Determination Actual slope, Calculation and Time modes
Sample ID Numeric, Numeric incrementing, alphanumeric or turned off
Modes of Operation Standard or Concentration modes
Security Mode Programmable passcode to lock Setup menu
Graph Mode Graph of Temperature/Time and Percent/Time on display or optional printer
Display Quarter VGA with contrast adjustment (black on white or white on black)
Keypad Sealed membrane with audible tactile feedback
Keys Start/Stop, Paper Feed, numeric, decimal, Enter, 4 navigation and 4 soft keys
Optional Internal Printer Internal thermal, 40 character graphic
Printout Format Selectable header (3 lines), analyzer info, operator, Sample ID, Calibration info, program name, program parameters, interval print, weight info, result and signature line
External Input/Output Serial, USB and Ethernet
Internal Clock Date and Time International, Military or AM/PM
Audible Tone Key stroke, ideal weight met and end of test, selectable On or Off
System Status Indicator Lights Two tri-color LEDs (balance & heater) on front of heater module
Power Requirements 90-250 VAC 50/60 Hz self adjusting power supply
Dimensions (inches) 16 1/4 x 19 1/2 x 9 1/4 (L x W x H) combined modules
Warranty Period 2 years
The Mark 3 LTE is backwards compatible to many of the standard Mark 2 drying progams.

Omnimark Moisture Analyzer

>>Request Moisture Analyzer Info

Editorial    Disclaimer   Data Protection   GTC   © Copyright Sartorius AG 2004